The Crate Custom Built Animatronic Halloween Jump Scare Prop Monster in a Box
The Crate Custom Built Animatronic Halloween Jump Scare Prop Monster in a Box – Sinister Mechx – YouTube. Video will open in a new window. Built for the 2017 Halloween Season. I have to sell it to make room for new projects. The Evil Doctor Zombie Mechx is triggered by a wireless remote control. This give you more control over the prop than the standard Infrared Trigger found on many big box decorations. This was custom built by me. This is not something manufactured in a factory. Check out the video! Sinister Mechx, a home-haunt located just outside of New Orleans, custom-fabricates Halloween props for home-haunters and professional haunted houses within the Dark Attraction Industry. Sinister Mechx is guided by one simple principle: Make kids drop their candy! The Crate Mechx is literally a living work of art and would scare even the most hardened horror fan. The Crate Mechxs animation controller is custom programmed to create an intimidating and terrifying scare. The Crate Mechx is triggered using a Passive Infrared Sensor. Simply plug the transformer into any 110 volt electrical socket and connect the airline to an air compressor capable of producing 100 to 120 psi of pressure. The The Crate Mechx has been tested and re-tested, cycling several times to insure prop will work flawlessly. Sinister Mechxs jump scare props are plug-and-play and ready-to-run. Simplicity is the key. There are no complicated schematics or diagrams to follow. Plug in the individual components, connect the air compressor (not included) and an amplified speaker (not included), and plug in the transformer in a wall socket. All of Sinister Mechxs jump scare props are reinforced to withstand the rigors of repeat performances during the Halloween season. Or the disappointment when an overpriced Halloween decoration must be discarded after malfunctions when they are placed back in service after months of storage. Sinister Mechx jump scare props can be easily repaired in the event of an unexpected problem. I have no control over the use of any product and therefore expects the user to exercise good judgment as to the proper selection, installation, use and maintenance of any product. I assume no responsibility for damage or injury of any kind due to misuse or improper installation or application in any way by any person. Please be aware of the following important safety information before purchasing or using any of our props. Animated props are intended for intermittent use only. Many require a wall or handrail to separate them from your audience as they move quickly and may injure those too close. We accept NO responsibility for the misuse of animated props. Special care must be taken with pneumatic props to avoid injury. Make sure that no more than 120psi is supplied to any of our props. Most of our props only require < 80psi to operate. We recommend regulating props to the minimum air pressure required to properly operate. These props are powered by 110v AC. Please be aware that shock hazards may exist if water or other liquids are allowed contact with the prop controller, the solenoids, and/or the props. User should wear ear protection if repeatedly exposed to air noise. When setting up pneumatic props, never add air until the prop is mounted securely. When adding air, first check that all tubing and fittings are mounted securely, then stand away from the prop and carefully connect the valve to the air supply. When working with pneumatics, always start with your air pressure low and your flow controls open to a minimum then work up the pressure until you achieve the effect you are looking for. Also always disconnect the air when working on or with one of these props. You never know when the solenoid may fire and its not going to stop for your face or body parts. All my props are designed to operate between 30-120 PSI. Failure to stay within these parameters will void any and all product warranties, and is extremely dangerous. To ensure a long life of pneumatic products, proper water traps/ filter lubricators and pneumatic oil should always be used. If you use common sense and protect yourself from harmful tools and chemicals, there should be no reason that you cant have year after year of haunting enjoyment with all of your limbs intact. The item "The Crate Custom Built Animatronic Halloween Jump Scare Prop Monster in a Box" is in sale since Wednesday, October 18, 2017. This item is in the category "Collectibles\Holiday & Seasonal\Halloween\Current (1991-Now)\Props". The seller is "sinistermechx" and is located in Luling, Louisiana. This item can't be shipped, the buyer must pick up the item.
- Country/Region of Manufacture: United States